An instruction manual from Tamiya...
★ CITY TURBO RACER ★ |
WR-02 CHASSIS
1983年發售Honda City Willy's Wheeler 在2000年的田宮模型展中以限量車殼的方式出售，利用WR-02底盤可以改造為City Turbo Willy Racer，改造後性能比WW2更好。以下改裝內文編譯自日本田宮模型官方網站，目前網頁業已移除，加上我的一些完工圖片。 |
Released in 1983, the "City Turbo Willy Racer " is a popular car. The limited body set is sold in "Tamiya Modeller's Gallery" in 2000. This is an easy modification project with the WR-02 chassis. It runs energetically with sharp acceleration quite different from Wild Willy 2. |
改造重點 |
Features |
■ 前懸吊 |
■ Front suspension |
■ 後懸吊 |
■ Rear Suspension Use "TG10 wheel axle" instead of the MA10 wheel axle, and expands the tread by using B14 parts (unused parts). Moreover, if TL-01 stabilizer set is installed to improve the stability,part of gear box is interfered, cut down a little to install. |
■ 輪胎 <imgage> 使用RC Boys 4WD Voltec Fighter 用的前後輪胎框組。 |
■ Tires and wheels Use tire and wheel set from RC Boys 4WD |
■ Dampers Use TA03 low friction damper set with on-road springs, red for front and blue at rear. |
|
■ 前車殼柱 原來不用的C5與原裝避震筒C2組合、中間找一支夠長的連桿兩邊以螺帽固定。 <imgage> |
■ Front Body Mount Assemble C5 (unused part) and C2 (friction damper parts of the kit), fix them with a long threaded rod. |
■ 後車殼柱 將C8與C20固定在底盤組件F1, F2之間，使用4個3x20mm自攻螺絲。C8與C20用2mm螺絲固定。<imgage> |
■ Rear Body Mount Fix C8 and C20 in between the main chassis parts F1 and F2 with 4 3x20 tapping screw. Use 2mm screw to connect C8 and C20. |
■ 馬達
|
■ Motor The top speed may fall due to a smaller diameter wheels are installed. Use high performance motor such as Dyna Run Eacing Stock with 20T pinion gear. Moreover, because of the high rotation please replace all plastic bushings in the the gear case with 1150 ball bearings. |
■ 轉向 轉向伺服臂E5改用原來不要的B10，此外利用C6作連桿以3x14mm自攻螺絲連結Knuckle。<imgage> |
■ Steering |
■ Body Shell The holes for mounting the body on the bonnet and the rear roof both are 5mmrespectively. Body may interfere with the wheelie bar, please cut off. |
|
■ Misc. The battery cover E3 is interfered with the body on the pipe portion, please cut off. |
|
請注意本網頁僅提供改裝資訊不負責改造過程與結果。 The information on this page is for your modification reference only, No responsibily for its process and outcome. |
|
Specification |
Dimention and weight |
●全長 Lengt =335mm ●全幅 Width =215mm ●全高 Height =170mm ●最低地上高 Ground clearance =15mm ●全備重量 Full weights =1,760g ●底盤長 Chassis length =310mm ●軸距 Wheelbase =185mm |
Chassis |
●材質 Material=ABS＋Polycarbonate ●形状= Monocoque typ |
Steering |
●形式=等長2分割式 Type of division in 2 equal length |
Suspension |
●形状=double wishbone F and R ●Dampers = F and R TA03 super low friction |
Drive Train |
●Midship rear-drive 2WD ● 動力源=Dyna Run Racing Stock
●Gear ratio=1：16.5 (20T) ●Diff gear=3 bevek type ●速度控制=ESC |
Tire |
● 輪幅 Tire tread F/R=29mm/42mm ●Diameter= F/R 75mm ●Wheel F/R=Voltec Fighter ●Tire F/R=RC BOYS 4WD Slick tires |
Body |
●材質=Styrene |
Part List |
ITEM58242 |
Wild Willy 2 kit |
13,800円 |
SP.356 |
20T･21T AV Pinion set |
350円 |
SP.591 |
5mm Ball collar (5 pcs) |
150円 |
SP.761 |
RC Boys 4WD Front slick tire set (2 pcs) |
500円 |
SP.762 |
RC Boys 4WD Rear slick tire set (2 pcs) |
600円 |
SP.763 |
Voltec Fighter front wheel set |
500円 |
SP.764 |
Voltec Fighter rear wheel set |
550円 |
SP.823 |
TG10 wheel axle (2 pcs) |
450円 |
OP.163 |
Spring set on-road type (For 4WD, FF series and Rally) |
800円 |
OP.272 |
Dyna Run Racing Stock Motor |
2,500円 |
OP.280 |
TA03 Super low friction damper set |
4,500円 |
OP.318 |
RC Boys 4WD Inner sponge for front tire |
150円 |
OP.319 |
RC Boys 4WD Inner sponge for rear tire |
150円 |
OP.324 |
TL-01 Stablizer set (F/R) |
450円 |
Misc screws and nuts etc |
||
※ Original content of this page was updated on May 2000 <Japanese 日文版>
原網頁更新時間2000年5月，同時刊登於6月份的「ラジコンマガジン」 八重洲出版 定価510円
